Point Cloud for Bricscad is a reverse engineering plug-in for Bricscad. This plug-in gives Bricscad the ability to reconstruct the geometry of an object from a point cloud which describes it.

Point Cloud for Bricscad can drape a surface over a point cloud or wrap a mesh around a point cloud. Draping a surface is similar to laying a piece of cloth over an object. The surface is deformed to take the shape of the object along the drape direction. A surface can be draped along one of the six orthogonal directions (top, bottom, front, back, right and left) or a custom user specified direction. Wrapping a mesh is similar to wrapping cloth all around an object to close it completely. Point Cloud for Bricscad has the ability to wrap a mesh around a concave or a convex point cloud.

Point Cloud for Bricscad is designed to be extremely user friendly and easy to understand. It adds new commands to Bricscad and also a sub menu called "PointCloud" which houses these commands.

Point Cloud for Bricscad is very easy to use as it adds a new command to the Bricscad powered application called "PointCloud".

System Requirements

Below is the hardware, software and operating system requirements for Bricscad plug-ins running on the Microsoft Windows platform. 

• Bricscad (32 Bit only): 8, 9, 10 and 11
  
  
• Operating System (32 Bit only): Windows XP SP2 or later, Windows Vista and Windows 7
  
  
• RAM: 1 GB (Recommended 2 GB)

Download & Purchase

Please download a fully functional trial of Point Cloud for Bricscad by clicking on the "Download Now" button below. To start using the software, you need a license key. A license key can be of two types: Trial or Permanent. A trial key is issued to you on the purchase of '7 day license' so that you may try the software before you purchase a permanent key. A permanent key is issued after you have purchased a license. We are confident that during the trial period (7 days with unlimited runs) you will find Point Cloud for Bricscad extremely useful. Later when you decide to buy the software please return to this page and click the "Buy with/without Subscription" button to place your order. Upon verifying the order you will recieve an e-mail with instructions on how to obtain your permanent key. We will create and send you your Key by e-mail within one business day. To avoid disruption in your workflow we urge you to place your order before the trial period ends.

		2.30 MB
		$4.99
		$299
		$249

IMPORTANT! Purchasing a Subscription is highly recommended since it the most cost effective way of keeping your software up to date. Moreover, Subscription entitles you to get a second free perpetual license for your laptop, among many other benefits. For details please read the SYCODE License and Subscription Frequently Asked Questions (FAQ).

Our licenses are single computer licenses and are locked to each computer they are installed on. Basically, the license key is specific to the computer's Host ID (the MAC address of the computer), and will not work on another computer. The installer picks up the physical MAC address of the network card connected to the computer which is basically “Ethernet adapter Network Connect Adapter”. So unless you change your network card, the key will always work even if you reinstall your operating system. If your internal network is periodically assigning a different Host ID to your computer, then please find a solution for this with your IT department.

Note: Downloading this software indicates your acceptance to the SYCODE Software License Agreement. The price mentioned above is for a single user license. For your bulk-licensing needs please contact us.

Installation & Usage

Since Point Cloud for Bricscad is a plug-in for Bricscad, it must be loaded into the Bricscad environment before it can be used. Please follow the simple instructions in the Point Cloud for Bricscad ReadMe document which is copied into the installation folder. If you accept the default values in the installer, Point Cloud for Bricscad will be up and running within a minute. However, if you choose to modify the values (for example, install the software at a location other than the default) then you will have to take extra care to see that Bricscad and the Point Cloud for Bricscad plug-in are properly setup and recognize each other. For an easy and straight forward installation, simply run the installer and accept the default installation options.  After you have loaded the plug-in file into Bricscad, simply click on the menu items in the "PointCloud" submenu to run these new commands. Truly, software made simple!

The 'PointCloud' menu consists of the following commands:

• PCImportPoints - Imports a point cloud from a text file
  
  
• PCDrapeSurface - Drapes a surface over a set of a point cloud
  
  
• PCWrapMesh - Wraps a mesh around a point cloud
  
  
• PCHelp - Displays the Point Cloud for Bricscad help file
  
  
• PCRegister - Registers your copy of Point Cloud for Bricscad
  
  
• PCAbout - Displays the Point Cloud for Bricscad about box

The PointCloud submenu

Point Cloud for Bricscad comes with detailed documentation for each command as well as a tutorial to get you started in the shortest possible time.

The Point File Format

A Point file format is basically a text file containing the x, y and z coordinates of a point on each line. Usually the coordinates are stored in the XYZ order. However, points are sometimes stored in the YXZ order. This is common in survey data where the YXZ order is referred to Northing, Easting and Elevation. Sometimes each point in the point file has a point number and/or description. An example of a point file with points stored in the XYZ order and has point numbers and descriptions.

1,5.678232,3.282384,6.112837,First Point
2,7.802343,6.792039,2.489561,Second Point
3,2.454512,7.453219,3.454865,Third Point
... and so on

Customization

If you want Point Cloud for Bricscad to work in a different way to suit your workflow, do let us know. We will customize the plug-in to suit your needs.

Related Products